Troubleshooting the w1110 (1E27, 1E35, 1E40, 1E41, or 1E45) label printer

Products affected: w1110 (1E27, 1E35, 1E40, 1E41, or 1E45) label printer, PitneyShip®, PitneyShip® Pro, PitneyShip® Enterprise, SendPro® C Series

Note: The w1110 label printer has different model numbers (PCNs) depending on how it was purchased. With the SendPro C it is 1E35, with the SendPro C Auto it is 1E40, with the networked SendKit it is 1E41, and as a standalone workstation printer it is 1E27 or 1E45.

There are several things you can try if the w1110 printer isn't printing or feeding properly, or if its lights are flashing or red. The normal state is for the green light to be solid.

In this article:

Poor print quality

If the print quality is poor (faded print, unreadable bar codes, streaks, etc.) when printing labels with a w1110 printer, try these steps.

Solution 1: Close the cover

Ensure that the cover is closed tightly by firmly pressing down on each corner of the cover.

If the issue is not resolved, try solution 2.

Solution 2: Clean the printhead

  1. Turn off the power switch and unplug the printer.
  2. Open the printer. Wait a few minutes for the printhead to cool.
  3. Remove the labels.
  4. Using a cotton swab moistened (not soaked) with isopropyl alcohol, thoroughly clean the printhead. Remove any debris or label material on the rollers and printhead.
    Cleaning the w1110 printhead
  5. Reinstall the labels, close the printer, plug it back in, and turn it on.

Green light is flashing

If the green light is flashing on a w1110 printer, try these steps.

Solution 1: Take the printer out of standby mode

  1. Press the Pause button on the printer's cover.
    W1110 printer pause button

If the issue is not resolved, try solution 2.

Solution 2: Restart the printer

  1. Turn the printer off and wait 60 seconds.
  2. Turn the printer back on. The LEDs will flash red and green for about 30 seconds while the printer restarts.

If the issue is not resolved, try solution 3.

Solution 3: Reinstall the paper roll

For instructions, see:

Red light is flashing

If the red light is flashing on a w1110 printer, try these steps.

Solution 1: Ensure that the printer cover is closed tightly

If the issue is not resolved, try solution 2.

Solution 2: Reinstall the paper roll

For instructions, see:

If the issue is not resolved, try solution 3.

Solution 3: Realign the roll feed

Refer to the Printer button diagrams below if needed.

  1. Open the printer’s top cover and feed the label so that it is ¼ inch out of the printer. Close the cover.
  2. Press and hold the Stop/Resume and the Feed/Cancel buttons simultaneously until the rollers begin to move the media. (See Printer buttons diagrams below.) Immediately release both buttons when the media begins to move. The media should advance one label and the left LED should be solid green.

If the issue is not resolved, try solution 4.

Solution 4: Turn the printer off and back on

  1. Turn the printer off for 60 seconds.
  2. Turn the printer back on. The LEDs will flash red and green for about 30 seconds while the printer restarts.

If the issue is not resolved, try solution 5.

Solution 5: Clean the printhead

  1. Check for and remove any debris or label material on the rollers and printhead.
  2. Turn off the power switch and unplug the printer.
  3. Open the printer. Wait a few minutes for the printhead to cool.
  4. Remove any installed media. Using a cotton swab moistened (not soaked) with isopropyl alcohol, thoroughly clean the printhead.

 

Printer feeds the wrong size, or the printer light is solid red

Solution 1: Restart the printer

  1. Unplug the power cord. The screen turns off after 10 seconds.
  2. Wait 30 seconds.
  3. Plug the power cord directly into a wall outlet. Make sure that the wall outlet is functioning correctly.
  4. Quickly tap and release the power button to turn the device back on. The LEDs will flash red and green for about 30 seconds while the printer restarts.

If the issue is not resolved, go to solution 2.

Solution 2: Reset the printer

Refer to the Printer button diagrams below if needed.

  1. Open the printer’s top cover and wind the labels back onto the roll so that it is clear of the feed rollers and sensors, then close the cover.
  2. Press and hold the reset button on the back of the printer. Continue holding this button while you perform the next step.
  3. While still pressing the reset button, press the Stop/Resume and the Feed/Cancel buttons simultaneously until the left LED on the front panel turns solid green, then release all of the buttons.
  4. Open the printer’s top cover and feed the roll so that it is ¼ inch out of the printer.
  5. Press and hold the Stop/Resume and the Feed/Cancel buttons simultaneously until the rollers begin to move. Immediately release both buttons when the label roll starts to move. The roll should advance one label and the left LED should be solid green.

Printer buttons

Front View

Datamax W1110 printer front view

  1. Cover Latch Release
  2. Stop/Resume
  3. Power LED (Green)
  4. Error LED (Red)
  5. Feed/Cancel

Rear View

Datamax W1110 printer rear back view

  1. Power Switch
  2. DC Power Inlet
  3. Reset Button
  4. USB 2.0 Port
  5. Ethernet/Network Port

The features and options you see may vary depending upon your role and subscription. If you have any questions regarding your permissions, please contact your administrator.

UPDATED: November 18, 2026